Skip to content

Furniture from original aircraft parts. Made in Italy.

Request
information
Long-range twinjet · 1982–1998 · 255 built

Airbus A310 cowling bookcase and wall sculpture

The two pieces that come from the A310 begin with the same component: the engine intake ring. External diameter 265 cm, internal 210. Those two measurements say which engine it came from, and almost which one exactly.

The pieces that come from it

2 in the catalogue

The Airbus A310 flew on 3 April 1982, was certified on 11 March 1983 and entered service in April 1983 with Swissair and Lufthansa, who had ordered it together in 1979. Production closed with the last delivery on 15 June 1998, to Uzbekistan Airways, after 255 aircraft.

It began as a shortened A300, 6.95 m less fuselage, but it is not only that: it has a new, smaller wing of 219 m², with the wingtip devices Airbus would later reuse on the A320 and A380, and a new tailplane. And it is the aircraft that brought two things into service that were to become normal: the two-crew cockpit, without a flight engineer, with six screens in place of the instruments, and (on the series 300, from 1985) a carbon-fibre fin. Airbus calls it «a pioneering use of carbon-fibre composites in airliners»: over 250 kg saved on a primary structural component. From then on composites entered the load-bearing structure of civil aircraft.

Which engine this intake came from

Four engines were certified on the A310: the General Electric CF6-80A, fan diameter 219.5 cm; the CF6-80C2, fan 236.2 cm; the Pratt & Whitney JT9D-7R4, 237.2 cm; and the 94-inch PW4000, 238.8 cm.

Our ring has an internal diameter of 210 cm. The throat of an intake is narrower than the fan it feeds (that is elementary aerodynamics), and that contraction is normally between 10 and 15 per cent. A 210 cm ring cannot have fed air to a 219.5 cm fan: that would be a 4% contraction, far too little. The CF6-80A is ruled out. That leaves the group of three engines at 236–239 cm, which differ from each other by two centimetres and cannot be separated by this reasoning.

The external measurement tries to separate them. General Electric publishes, on its own site, the «maximum diameter» of the CF6-80C2: 106 inches, that is 269.2 cm. Our piece measures 265. That is one and a half per cent of difference, the closest match we found in the whole search. For the JT9D-7R4 and the PW4000 an equivalent figure is not published, so we cannot make the same comparison: they are not ruled out, they are simply not verifiable.

The honest conclusion is this: almost certainly a General Electric CF6-80C2, with the JT9D-7R4 and PW4000 still possible. One fact points the same way: the two groups of A310s still in service and being retired today — the Canadian CC-150 Polaris and half the German tanker fleet — carry CF6-80C2s. Those are the airframes reaching teardown now.

What that ring is, exactly

It is not a piece of curved sheet. The intake of a turbofan is an acoustic sandwich: a perforated inner skin, honeycomb beneath, a closed outer skin. Each hole with its cell is a small resonator that absorbs the fan's noise. If you look closely at the inner surface of these two pieces, those holes are visible: they are not decoration, they are the reason modern engines are heard less.

Through the leading lip, then, passes hot air bled from the compressor that stops ice forming on the edge. On engines of this generation the lip is typically aluminium, with titanium strips where erosion demands; the real titanium sits further back, in the fan containment ring.

The panel is whole

The A310 engine cowling cut clean through: the three layers are visible one on the other — outer skin, honeycomb core and perforated inner skin.
The acoustic panel in section: skin, honeycomb, perforated liner

The perforated inner skin is the original one, and the honeycomb is still behind it. On the sectioned piece the three layers can be seen one on the other: the smooth outer sheet, the honeycomb, and the micro-perforated skin facing the airflow. Those holes are not decoration: they are the intake's acoustic absorber, and they work only with the honeycomb behind them. Having both means having the acoustic panel whole.

Assembly number stencilled on the outer skin: ASSY 224-2131-521-01, MOD68, 392 AND ON, CUM 0445, with an oval inspection stamp.
The assembly number, with the effectivity note «392 and on»

Stamped on the outer sheet is the assembly number: ASSY 224-2131-521-01, with MOD68 below it, 392 AND ON (the applicability note, that is, from which aircraft onward) and CUM 0445.

The evidence

The plates and markings photographed on the pieces. They are what this page rests on: where there is no plate, the page says so. The serial number visible on each of them belongs to the component that was photographed: every piece carries its own, and it is written on the certificate that comes with it.

Sources for this page
  1. Airbus A310 — Wikipedia
  2. Airbus — the evolution of materials and the carbon fin
  3. GE Aerospace — the CF6 engine family and its dimensions
  4. General Electric CF6 — Wikipedia
  5. Pratt & Whitney JT9D — Wikipedia
  6. Pratt & Whitney PW4000 — Wikipedia
  7. CC-150 Polaris — Wikipedia
  8. NASA — nacelle acoustic liners (CR-2002-211672)
  9. Aircraft Commerce — A300-600 and A310 specifications

The pieces that come from it ↑