Skip to content

Furniture from original aircraft parts. Made in Italy.

Request
information
Twin-engined airliner · from 1967 · more than 12,500 delivered

Boeing 737 jet engine coffee tables

Three coffee tables and a mirror made from the JT8D engine of the Boeing 737: compressor, fan and exhaust mixer. Of the four pieces that come from the 737, one dates itself. The exhaust mixer (the lobed ring at the engine outlet) can only come from a 737-100 or -200: no 737 built after 1988 ever had that part.

The pieces that come from it

4 in the catalogue

The Boeing 737 first flew on 9 April 1967 and entered service with Lufthansa on 10 February 1968. It has since been built in four generations: Original (-100 and -200), Classic (-300/-400/-500), Next Generation (-600/-700/-800/-900) and MAX. More than 12,500 have been delivered. For over fifty years it was the most-delivered airliner in history: the Airbus A320 family passed it in October 2025.

The piece that dates itself

The exhaust mixer is the lobed ring at the engine outlet. Its job is to mix the cold air that has bypassed the hot core with the scorching gases coming out of it, before the jet reaches open air: two mixed flows make less noise than two flows meeting abruptly.

On the 737 that part exists in one configuration only, and the source is the FAA's type certificate data sheet for the Boeing 737, A16WE. Under the -100, the -200 and the -200C the same sentence appears: JT8D-15 engines fitted with the MOD 10 exhaust mixer, Pratt & Whitney part number 5004027, have the same limits as JT8D-15s with the splitter-type exhaust. It is a certified part, with a part number, fitted to one specific engine.

From 1984 the 737 changed engine: the CFM56 arrived, first the -3 on the Classics and then the -7B on the Next Generation. And the CFM56 has no mixer: it exhausts the two flows coaxially, separately. This is not a 737 peculiarity. In the whole CFM56 family the only mixed-flow version is the -5C, the Airbus A340's, and the British authority's type certificate says so in writing: «separate flow for CFM56-5B engines, mixed flow for CFM56-5C».

The conclusion is blunt. A 737 lobed mixer comes from a JT8D; the JT8D was on the 737 only in the -100 and -200 series; the last -200 was delivered to Xiamen Airlines in August 1988. That part was therefore built between 1967 and 1988. There is no need to take it on trust: it is a chain of documents.

One clarification, because it matters in the workshop too. The FAA technical report describing the JT8D mixer in detail — twelve lobes, built in Inconel 625 for the lobes and the cone, Inconel 718 for the struts — covers the 727 and DC-9 versions, not the 737 one. Same engine family, same programme, same years: it is a reasonable deduction, not a citation. But the material is the important thing: Inconel is a nickel superalloy, not aluminium. It is there because it works in the hot jet. It does not polish like a cowling and it does not behave like a cowling.

Fan and compressor, in plain words

In a turbofan the incoming air splits in two. The small part goes into the core of the engine: it is compressed, heated by burning kerosene, and drives the turbines. The large part (in the JT8D almost half, in modern engines eighty per cent and more) passes around the core without ever burning, pushed by the front fan alone. The fan is in effect a ducted propeller, and it provides most of the thrust.

The compressor is what sits immediately behind, and works only on the core air: it compresses it stage by stage before combustion. The JT8D has thirteen stages: six low pressure (the fan is the first of these) and seven high, followed by nine can-annular combustion chambers, a single-stage high-pressure turbine and a three-stage low-pressure one.

The materials follow the temperature. The fan blades and the first compressor stages are titanium alloy, which weighs little and holds up to about 350 °C. Further back, where it is hotter, you move to nickel superalloys: heavier, but the only ones that hold.

The hamster pouch

There is a simple way to tell which engine a fan came from: measure it. The JT8D fan is 101 cm across. The CFM56-3 fan is 152 cm. The CFM56-7B, 155 cm. Between the first and the second there are fifty centimetres of difference, and those fifty centimetres produced the most recognisable oddity in all of civil aviation.

The 737 was born short-legged: the short undercarriage was there so it could be loaded and unloaded without ground equipment, at airports that had none. When the CFM56 arrived in the 1980s, with its much wider fan, the engine no longer fitted under the wing. Lengthening the undercarriage would have meant redesigning half the aeroplane. Boeing took another route: it moved the accessory gearbox from underneath the engine to its side, and flattened the bottom of the intake. Since then the 737 has had a nacelle that is not round but flat underneath: they call it the hamster pouch.

This difference lets the pieces be dated without hunting for a data plate, because we have the measurements. The collection's two fans measure 98 cm in diameter, the compressor 102, the mixer 93. The JT8D case is 101.6 cm wide and its fan 101.3: a rotor taken out of its casing always measures a few centimetres less, and that is exactly the gap we find. The CFM56-3 fan is 152 cm across: fifty-four centimetres more than ours. There is no room for doubt.

So all four pieces on this page (the two fans, the compressor and the mixer) come from a Pratt & Whitney JT8D, and on the 737 that engine was fitted only to the -100 and -200 series. They are pieces built between 1967 and 1988. It is not a supposition: it is a comparison between measurements taken in the workshop and the published diameters of the two engines.

Twelve lobes

Counted: there are twelve. The FAA technical report on that engine's mixer gives twelve, and the piece in the workshop has twelve. What was a possible check has become a check made.

Number stamped on the mixer flange: 806473E, with the serial BWPTAH 9472; the lobes show on the right.
The number on the mixer flange, with the lobes on the right

Stamped on the mounting flange is 806473E with the serial BWPTAH 9472, the form of that manufacturer's part numbers.

The mixer's Inconel does not polish like aluminium: it is a superalloy made to resist high temperatures, and it resists abrasive too. Carlo's rule for the titanium of the DC-8 rivets applies here: hard alloys are polished separately, with different techniques, and mixing them with aluminium in the same pass is the quickest way to ruin both.

Why there are some to strip, and why a few still fly

Here too the reason is the Airport Noise and Capacity Act of 1990 and the 31 December 1999 deadline for Stage 3. Hush kits for the 737-200 were made by Nordam and AvAero, and by mid-1998 orders and options exceeded five hundred. But the -200 had been out of production for ten years, and most were scrapped.

About forty remain in service worldwide, and they survive for a very concrete reason: they are among the few airliners certified to operate from gravel runways. In northern Canada, where the runway is gravel and nothing else, the 737-200 still has no complete replacement. Nolinor has eight (about a fifth of all those still flying), and one of them, registered C-GNLK, first flew in May 1974: it is the oldest jet airliner still in service. Canadian North retired its last on 6 May 2023; Air Inuit is replacing its own.

It is a detail worth keeping in mind while looking at a piece on this page: the aircraft it came from was taken out of the sky by a noise law, and its last brothers are still flying because they can land where there is no tarmac.

The evidence

The plates and markings photographed on the pieces. They are what this page rests on: where there is no plate, the page says so. The serial number visible on each of them belongs to the component that was photographed: every piece carries its own, and it is written on the certificate that comes with it.

Sources for this page
  1. FAA — Type Certificate Data Sheet A16WE, Boeing 737
  2. FAA-RD-80-69 — JT8D Engine Internal Exhaust Mixer Technology Program
  3. UK CAA — TCDS UK.TC.E.00105, separate-flow CFM56-5B and mixed-flow -5C
  4. EASA — TCDS E.066, CFM56-2 and CFM56-3 engines
  5. Pratt & Whitney (RTX) — the JT8D engine
  6. The Museum of Flight — Boeing 737-130, the first one built
  7. NASA Glenn — how a turbofan works
  8. b737.org.uk — the 737 powerplants, from JT8D to CFM56
  9. 49 U.S. Code § 47528 — the Stage 3 deadline
  10. FlightGlobal — hush kits for the 737-200, 1998
  11. Avgeekery — Nolinor, the world’s largest 737-200 operator
  12. Titanium in the Gas Turbine Engine — Swansea University

The pieces that come from it ↑